- #Xbox chimp download how to#
- #Xbox chimp download install#
- #Xbox chimp download upgrade#
- #Xbox chimp download iso#
If you know you have your eeprom backup in the tmp folder, choose option 2. It will now ask you where the source key is located. Now, before leaving Chimp, we have one more thing to do, lock the drive. When it is complete, choose EXIT to return to the menu. Just bare with it and eventually it will finish. It will take a little while to clone the drive and the time it takes depends on how much data there is to clone. Choose YES to continue.ĭo the clone 'Full Disk' when asked (sometimes referred to as Byte by Byte). Again the system will ask you to make sure all IDE devices are connected. Providing both HDD's were detected in step 9, now choose option 2 ('Clone Master to Slave'). When it has finished scanning, scroll up and down the results to make sure that both HDD's have been detected. The system will tell you to make sure you have connected all of your IDE devices before continuing.Ĭhoose YES to continue. On the Main Menu of Chimp, first select option 1 ('Scan Physical IDE Devices'). Plug the cable now into your new HDD (so we now have original HDD power and IDE, new HDD power and IDE, DVD no IDE but power). When Chimp starts and you are presented with the first menu screen, fully remove the IDE cable from the DVD drive. Launch Chimp from the Applications menu in your dashboard.
Power on the Xbox and allow to boot into dashboard. (So currently, original HDD has IDE and power, new HDD has power only, DVD drive has IDE loosened and power). The Xbox will not boot if the IDE to the DVD is removed completely at this point. Loosen the IDE cable plugged into the back of the DVD drive, but do not remove it. Now, use the Molex splitter to plug power into both original and new HDD's. Now open the Xbox using the Torx screwdrivers. Make sure the jumper on the back is set to SLAVE (not MASTER, not CABLE SELECT).
#Xbox chimp download upgrade#
Before opening your Xbox, unwrap and examine your new HDD (the one you intend to upgrade to). A Molex Y-Splitter, or some way to power new HDD as well as original.installed as an application on the Xbox.If you experience lack of functionality while Chimp is running, please connect up a MS controller. NOTE: Some people have experienced problems when using a third party controller.
#Xbox chimp download how to#
Published by on Category: Apps Page Views: 93,550 Introduction Following a recent spate of interest and questions regarding the use of Chimp, I have complied this step by step guide on how to use the program in order to upgrade your HDD. SEARCH TUTORIALS How to use Chimp: A step-by-step guide.
This guy has some videos I found very easy to follow. I guess most of this info is useless if you're just trying to access the extra 2gb on the seagate drives. Finally go into your settings in the dashboard and there should be an option to look for the g partition. I max out the f partition to 256gb then I put the rest on the g partition. Jump forward past the softmod, and now I want to clone my hard drive I clone and lock the hard drive then I go down to partition my slave drive. My hard drive was going to be bigger than 256gb so I went with the nkpatcher.67. Either you setup with the nkpatcher.06 or.67. Depending on how you selected to softmod your Xbox there are two ways to do your partition. I upgraded the ide ribbon from a 40 conductor to an 80 conductor (also known as ultra ide 133). I had some issues, and even a short lived success. I've upgraded a few Xbox with only the softmod.
I believe those options should be in chimp. Does anyone of you have an idea how i could fix this? According to the videos i've seen so far, there should pop up another menu in which i can choose how the hdd should be formatted. 5) when i finally hit 'yes' on when he asks me, wether the new hdd can be formatted ->nothing happens. Then i hit 'clone from master to slave', again it shows both devices. It recognizes both HDDs when i scan for them.
#Xbox chimp download iso#
Windows Xp Iso Image Download For Virtualbox Download. Used chimp to clone.Īfter booting i changed the IDE cable from the DVD drive to my new hdd. Before opening your Xbox, unwrap and examine your new HDD.
#Xbox chimp download install#
How to use Chimp to install a larger HD in your xbox - Microsoft Xbox Tutorials. To allow you to hotswap the internal hard disk with. 2) i've set the jumper on the original hdd to master, the jumper for my new hdd (80gb) to slave. What i have and have done: 1) i have a hard modded xbox (don't ask me what chip, someone modded this thing like over 10 years ago) with EvoX and UnleashX dashboard on it. So i tried out myself but i didn't suceed yet. Hey guys, i recently discovered some youtube videos where people showed how to upgrade the original xbox's hdd to a bigger one without any problems by using chimp. I used an xbox program called Chimp to clone to a bigger hard drive (I think the version is 2.4 or 2.6).
0 kommentar(er)
